Plumbing Essentials: A Prerequisite for When Installing a Bathtub

Click Here

We have come across the article involving Tools You Need to Install a New Bathtub directly below on the web and concluded it made good sense to relate it with you in this article.


How to Install a Bathtub Yourself
Mounting a tub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a new one is also a moderately hard project. If the old tub is conveniently obtainable, the job can move quickly; if you need to open a wall to remove the old tub and also place the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to move out the old tub and set in the new one. Ensure you have actually qualified on your own for the task as well as are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider using one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your restroom if you have actually currently bought a new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your tools and also product list ought to consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Setup


    To start with, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid stress on the bathtub.
    Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.

    Removing Old Touches


    If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the limited accessibility that is frequently the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel ready for the continuing to be water that will come from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
    Before carrying on to fit the brand-new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Using the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub till the level reviews level.
    To install faucets, fit all-time low of the outermost flexible faucet port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
    Turn on the water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leaks.
    Lastly, deal with the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub should wait up until the tub has actually been made use of at least once as this will certainly settle it into its final setting.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind ought to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and also the tiling, resulting in issues with dampness and also possible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are sold in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles using waterproof or waterproof adhesive as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    We hope you liked our post about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking a few minutes to read our piece of content. Sharing is nice. You never know, you may be helping someone out. Thanks a lot for going through it.


    Overflow? Ring now!

    Leave a Reply

    Your email address will not be published. Required fields are marked *